|
| Author |
Message |
|
tommypic
|
Post subject: Topside wont turn up heat  Posted: Wed Nov 28, 2007 6:44 am |
Joined: Wed Nov 28, 2007 5:54 am
Posts: 5
|
|
I have a Icon Image 15 with Balboa spa pack , topside controls wont turn heat up but will turn down . It is a 4 button panel and the light button dont work either and yes the bulb and fuse are good . It just heats to factory settings which are 100
Heat - Up
Light - On /Off
Jets
Heat - Down
|
|
 |
|
 |
|
Pageup
|
Post subject: Posted: Fri Nov 30, 2007 9:54 pm |
| Site Admin |
 |
Joined: Tue Feb 03, 2004 11:39 am
Posts: 1409
Location: Metro Atlanta, Georgia Region
|
|
You didn't say if this was new, used, previously worked or what not, but based on what you said i'd replace the complete control unit.
_________________
Use this information at your own risk!
http://spapartsnet.com
http://atlanta.spanet.net
Amateurs built the Ark, Professionals built the Titanic.
|
|
|
|
|
|
|
tommypic
|
Post subject: Posted: Mon Dec 03, 2007 5:01 pm |
Joined: Wed Nov 28, 2007 5:54 am
Posts: 5
|
|
The unit is 4 yrs old and it did work .
thanks
|
|
|
|
|
|
|
Pageup
|
Post subject: Posted: Mon Dec 03, 2007 5:06 pm |
| Site Admin |
|
Joined: Tue Feb 03, 2004 11:39 am
Posts: 1409
Location: Metro Atlanta, Georgia Region
|
|
Ok so then if you turn it down to say 90 degrees, it goes up to 100 and stops? Does it actually heat then, and do the jets work?
_________________
Use this information at your own risk!
http://spapartsnet.com
http://atlanta.spanet.net
Amateurs built the Ark, Professionals built the Titanic.
|
|
|
|
|
|
|
tommypic
|
Post subject: Posted: Mon Dec 03, 2007 6:56 pm |
Joined: Wed Nov 28, 2007 5:54 am
Posts: 5
|
|
If I turn it down to say 90 degrees it wont turn back up . I have to shut off main power to spa and then back on , then it goes to factory setting of 100 degrees . The jets work fine and it does heat to 100 degrees but cant turn up
thanks
|
|
|
|
|
|
|
Swine
|
Post subject: Posted: Mon Dec 03, 2007 11:53 pm |
Joined: Sun Apr 03, 2005 12:50 am
Posts: 921
Location: SW Florida
|
|
Try unplugging the topside from the control box, and plugging it in again. Shake it a little, wiggle it, try it loose, try it tight, and wiggle it again.
Doing a rain dance at the same time may be helpfull as well.
_________________
t'was a woman that drove me to drink, and I've never had the courtesy to thank her
|
|
|
|
|
|
|
tommypic
|
Post subject: Posted: Tue Dec 04, 2007 8:04 am |
Joined: Wed Nov 28, 2007 5:54 am
Posts: 5
|
|
Page , I just replaced the top side controls . Light now works but temp still wont turn over 100 degrees .
Thanks
|
|
|
|
|
|
|
Swine
|
Post subject: Posted: Tue Dec 04, 2007 9:15 am |
Joined: Sun Apr 03, 2005 12:50 am
Posts: 921
Location: SW Florida
|
|
Look closely for corrosion or bent pins on the PCB where the topside cord plugs into the control box.
If that's not it, new PCB.
Try earlier suggestion as well.
_________________
t'was a woman that drove me to drink, and I've never had the courtesy to thank her
|
|
|
|
|
|
|
|
